Recent content by matt167

I watched Dawids video before I bought the card. I looked at the A2000 but more money for less performance at the moment. It’s crazy he got that working though. I am using a 2x sata to 8 pin adapter too. But I bought a good one from Cable Matters and ive closely monitored it a couple times.

. What I’ve read is that the cpu cooler is attached to the motherboard tray with 6-32 screws and using the AMD screws on the Intel bracket with an ID cooling cooler will work. Only what I’ve read tho.. but the cpu doesn’t overheat. The I5 8500 gets to 70* gaming. The 4060 right around 60w of...

Going to need some ideas for cooling.. I removed the plastic cpu duct and did more testing. GPU never really got over 80* but the cpu runs hotter now ( safe temps tho ). Now I have room for a 60mm fan.. The 3.5” cooler didn’t fit the 3.5” slot due to using sliders and special screws so I...

Well it’s running. Power is not an issue. Thermals is a major issue… kinda I ran Heaven and it draws 115w on average and takes one cycle to get to 87*. I was just able to get a benchmark and then I cried uncle… Time spy ran a little colder because it was allowed time to cool in between…...

Okay cool. I just wanted to make sure. Wife will be happy it lights up green

My wife loves lime green. One of the surprises I did for her on the livingroom HTPC was put in a green LED fan… now that I have a HP z2, there is no place for that 80mm green fan.. I bought an LED strip that uses a magnetic strip to light it up.. I’m going to put in a 2.5” mechanical HDD just...

I went ahead and ordered the 4060. Onboard graphics Isn’t happy for some reason. Keeps switching resolution's on anything that uses graphics. Not sure why but I know it won’t be an issue with a new card. Wife couldn’t even watch a dvd ( yes it’s used for that too ) so told me I needed to do...

Yeah the Optiplex has the x16 slot right next to the power supply. The WX4100 was the most power in a single slot without going to a 6400 or breaking the bank on a Quadro that was only marginally faster I measured the Z2 and I have about 8” of usable length without cutting anything. So the...

Well I just bricked my WX4100. I found a bios for a Dell rx 560 which everything looked right ( my Wx4100 is a Dell card as well ) . Even had Samsung ram. Doesn’t work. I bet because of the 4x display ports. The cards are most likely very similar but it gets zero display…. With the HP...

I run at 1080P with it and it’s just a TV so everything will be capped at 60 fps via vsync. That should keep it from overheating as well as giving buttery smooth game play.

Will the stock CPU cooler work okay with the 4060s heat emission? It’s a decent tower but the fan on it is indirect. I can remove the tunnel shroud from behind it and install a 60mm fan but I’m not sure if it would affect performance. I have not bought the card yet but I ordered all the cables...

I’m hoping the Fox 3 3.5” cooler I ordered does the trick. I have a chain of 3 40mm fans from an old 5.25 cooler I have. Which I can put in the front I think I’m going to look into making the fan system thermostatic control so they only run if the case temp hits a certain temperature

Forgot to update this. The optiplex this replaces had 16gb of 2666 and it wasn’t matched brand and I never noticed.. I put that ram in the HP and it’s fine. The HP had a single stick of 8gb HP branded 2666. I’m contemplating going 4060 and running a 2x sata to 8 pin adapter. The psu is...

I’m thinking that the blower suction will be right in the front corner very close to the GPU fans and it may just be enough. The power supply intake vent would be directly behind it so it would almost be like a tee flow off of the GPU The cpu has its own duct out the back.

I used to use the PCI slot fans nearly 20 years ago. But never had one of the ever cool 3.5” coolers. Did they ever work okay? My new to me HP Z2 SFF has no fan slots and I know it’s going to have some amount of thermal issue so I either need to case mod/ make something or use a product from...